ClassicAutoParts.co

Driveline sourcing

Buying a Used Rear End: How to Identify the Gear Ratio and Axle Before You Pay

Used rear ends are among the most commonly swapped parts in the classic car world, and among the most commonly misdescribed. "Posi, 3.73, out of a Chevelle" in a listing can mean exactly that, or it can mean someone once heard that about it.

This guide shows you how to confirm what you're buying: the axle family, the ratio, whether it's really a limited slip, and the fitment details (width, spline count, brake setup) that decide whether it bolts into your car.

Why rear ends are hard to buy used

The same basic housing might have been built with half a dozen ratios, several track widths, different axle splines and either open or limited-slip carriers. Over decades, owners swapped gears, narrowed housings, changed axles and moved carriers between housings. The paperwork, if there ever was any, usually didn't come along.

That means the original application listed in an ad is only a clue. What you need is what's inside it now.

Step one: identify the housing family

Most American rear ends fall into two broad designs, and you can usually tell them apart from a photo of the back.

Integral carrier (removable rear cover)

A bolt-on cover at the back of the housing gives access to the gears. The number and pattern of cover bolts, plus the cover's shape, are a common first identifier. Many GM, Mopar and AMC units, plus some Ford designs, use this layout.

Drop-out / third-member (no rear cover)

The rear of the housing is solid, and the whole gear assembly comes out the front as a unit. The Ford 9-inch is the best-known example. Removable third members make ratio swaps easy, so check them carefully.

Once you know the design, compare the cover bolt count, cover shape, ring gear size and any cast-in numbers against a reference for your make. Club forums and interchange guides are useful here; see our interchange manual guide for where to look.

Step two: find the gear ratio

Factory tags and stamped codes

Many factories identified the ratio somewhere on the assembly. Depending on the make, that could be a metal tag held under a cover or carrier bolt, or a code stamped into an axle tube. These are useful, but tags get lost or moved when units are rebuilt, and gears may have been changed since. Treat a tag as a starting point.

Ring and pinion tooth count

If the cover is off or the third member is out, look on the ring gear. Many ring gears are stamped with the tooth counts of the ring and pinion, often shown like "41-11". Divide the larger number by the smaller to get the ratio. 41 divided by 11 is roughly 3.73.

Counting driveshaft turns

This works with the cover on, and it checks what's really inside. Safety first: the car must be properly supported on jack stands rated for the load, on level ground, with the transmission in neutral and the front wheels chocked.

  1. Raise the rear so both wheels are off the ground and support it securely.
  2. Mark the driveshaft and a tire sidewall with chalk or paint at the bottom.
  3. If both wheels turn together (a typical limited slip): rotate one tire exactly one full turn and count the driveshaft turns. That number is about the ratio.
  4. If the other wheel turns backward (a typical open differential): hold the other wheel still, rotate your marked wheel exactly two full turns, and count driveshaft turns. That number is about the ratio.
  5. Count carefully, including the fraction of the last turn. Three and three-quarters is a 3.73 or similar; three and a half is a 3.55 or similar.
Why two turns for an open diff? With one wheel held, the differential effectively doubles the turning of the free wheel. Rotating it two times gives the same driveshaft turns as both wheels turning once together.

Step three: open, limited slip or locker?

With both rear wheels off the ground, rotate one wheel by hand.

Limited-slip units need the correct gear oil and, for many clutch-type units, a friction modifier additive. Ask the seller what's been used. Unknown history is another reason to plan for a fluid change and inspection.

Step four: will it fit your car?

The ratio is what most people shop for. Fitment is what causes most of the trouble. Measure and confirm all of these before freight.

CheckHow to confirmWhy it matters
Overall widthMeasure wheel mounting surface to wheel mounting surfaceAffects tire clearance and wheel offset choices
Spring perch / mount locationsMeasure center to center and compare to your carLeaf spring and control arm mounts must line up
Axle spline countCount splines on a removed axle, or ask the seller toDetermines which axles, carriers and upgrades will work
Wheel bolt patternMeasure or confirm with a bolt pattern gaugeYour wheels must match, or the axles must change
BrakesDrum or disc; note the backing plate and parking brake setupBrake parts must suit your master cylinder and lines
Pinion yokeIdentify the U-joint size and styleMust match your driveshaft or you'll need a new yoke or U-joint
Axle retentionC-clip or retainer-plate designAffects service and parts, and some uses

The yoke and U-joint issue catches a lot of people. Our U-joint guide and driveline guide cover how to match them.

Picking a ratio for how you drive

A numerically higher ratio (like a 4.10) gives quicker acceleration and higher engine speed at a given road speed. A numerically lower ratio (like a 2.73 or 3.08) gives calmer highway cruising and less snap off the line. The right answer depends on your transmission, tire height and how you use the car.

If you've added an overdrive transmission, you can often run a steeper ratio than a stock three- or four-speed car would tolerate on the highway. Our 3- vs 4-speed swap guide covers some of that thinking. Note that changing the ratio also changes your speedometer reading, which may need a different speedometer drive gear.

Inspecting a used unit

If the car came with a whine or clunk, our rear end noise guide helps you understand what it might mean before you buy.

Safety-critical parts. Axle bearings, axle retention and rear brakes keep the wheels on the car and the car stopping straight. Have a used rear end inspected, and have gear setup or axle bearing work done by someone experienced, using the specifications in the factory service manual. See our rear axle bearing kits guide for the parts side.

Where to shop and how to research value

Complete rear ends, third members and carriers all show up regularly on eBay, at swap meets and through marque specialists. Use specific searches (housing type plus ratio, or carrier type plus spline count) and check completed sales, which give a much clearer picture of what similar units actually sold for than active asking prices do.

A bolt pattern gauge and a cheap digital caliper are worth keeping in your swap meet kit.

The bottom line

Don't buy a rear end on its listing title. Identify the family from the housing, confirm the ratio by counting turns or reading the ring gear, test the limited slip yourself, and measure everything that has to fit your car. Then budget for fresh fluid, seals and an inspection before it carries you down the road.

FAQ

What does 'posi' mean on a rear end listing?

It's shorthand for a limited-slip differential, from a trade name GM used. Sellers use it for any limited-slip unit, and sometimes for lockers. It doesn't tell you which design it is or whether the clutches are worn, so test it and ask.

Can I identify a gear ratio without opening the cover?

Yes. With the rear wheels off the ground, mark the driveshaft and a tire, then rotate and count driveshaft turns. Factory tags or stamped codes can help too, but the turn-counting method checks what's actually inside.

Is a rear end from a different model a direct bolt-in?

Rarely without checking. Width, spring perch or control arm mount locations, axle spline count, wheel bolt pattern, brake type and the driveshaft yoke all have to suit your car. Many swaps are well documented by enthusiasts, so research your exact combination.

Should I reuse the gears and bearings from a used rear end?

A quiet, smooth unit may be fine to reuse after inspection, but many builders replace bearings and seals as a matter of course. Gear setup (pinion depth, backlash and preload) is specialist work. If you change gears, have a shop that sets up differentials do it.

What does C-clip mean on a rear axle?

In some designs the axles are held in by C-shaped clips inside the differential, rather than by a retainer plate at the axle ends. It matters because a broken axle can behave differently in each design, and some racing sanctioning bodies have rules about it. Know which type you're buying and have it inspected.